battery_compatibility:axistorage
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
battery_compatibility:axistorage [2017-09-15 11:07] – [3. VEConfigure settings] edevries | battery_compatibility:axistorage [2019-08-15 12:18] (current) – replace venus-device with GX device guy_stewart | ||
---|---|---|---|
Line 7: | Line 7: | ||
==== 1. Introduction ==== | ==== 1. Introduction ==== | ||
=== 1.1 Compatible Victron products === | === 1.1 Compatible Victron products === | ||
- | All 48V Multis and Quattros. | + | All 48V Multis and Quattros. |
=== 1.2 Notes === | === 1.2 Notes === | ||
Line 15: | Line 15: | ||
* Minimum CCGX version is v1.72 | * Minimum CCGX version is v1.72 | ||
* The derating mechanism is not very precise yet. In other words, do not expect a discharge limit of 30A to result in a precise discharge of 30A. | * The derating mechanism is not very precise yet. In other words, do not expect a discharge limit of 30A to result in a precise discharge of 30A. | ||
- | * Actual charge- and discharge limits are visible in the Parameters page. See screenshot below in Chapter | + | * Actual charge- and discharge limits are visible in the Parameters page. See screenshot below in Chapter |
* AXIstorage batteries and MPPT Solar Chargers with a VE.Can communication port cannot be both connected to the CCGX, because of different canbus speeds. Use Solar Chargers with a VE.Direct comm. port instead. | * AXIstorage batteries and MPPT Solar Chargers with a VE.Can communication port cannot be both connected to the CCGX, because of different canbus speeds. Use Solar Chargers with a VE.Direct comm. port instead. | ||
=== 1.3 System diagram === | === 1.3 System diagram === | ||
{{ : | {{ : | ||
- | ==== 2. Wiring of communication cables ==== | ||
- | To use the AXIstorage ESS in Victron system, it is necessary to use a Color Control GX. The Color Control GX takes care of sending the necessary canbus keep-a-live message to the ESS battery. Without it, the battery will open its internal emergency relay after 10 minutes. | ||
- | A special RJ-45 cable is necessary to connect | + | ==== 2. GX device needed ==== |
+ | To use the AXIstorage ESS in Victron system, it is necessary to use a ColorControlGX or a VenusGX. The controller takes care of sending | ||
- | ^ Function ^ VE.Can | + | ==== 3. Wiring of communication cables ==== |
- | | GND | Pin 3 | Pin 2 | | + | Use the //VE.Can |
- | | CAN-L | + | |
- | | CAN-H | + | |
- | Place a VE.Can terminator in the empty socket on the CCGX | + | Then, plug a [[https:// |
- | ==== 3. VEConfigure settings ==== | + | More information about the cable can be found in [[battery_compatibility: |
- | === 3.1 General tab === | + | Without properly connecting this cable, the battery will stop charging/ |
+ | |||
+ | |||
+ | ==== 4. VEConfigure settings ==== | ||
+ | |||
+ | === 4.1 General tab === | ||
- Check " | - Check " | ||
- Set the battery capacity to 121.5 Ah | - Set the battery capacity to 121.5 Ah | ||
- The other parameters (" | - The other parameters (" | ||
- | === 3.2 Charger tab === | + | === 4.2 Charger tab === |
^ Parameter | ^ Parameter | ||
| Battery type | Lithium | | | Battery type | Lithium | | ||
Line 49: | Line 51: | ||
Note: make sure to double check the float voltage after completing Assistants, and if necessary set it back to 60.00 V. | Note: make sure to double check the float voltage after completing Assistants, and if necessary set it back to 60.00 V. | ||
- | === 3.3 ESS Assistant === | + | === 4.3 ESS Assistant === |
Select the fourth battery type: | Select the fourth battery type: | ||
Line 60: | Line 62: | ||
- | ==== 4. Color Control | + | ==== 5. GX device |
- | * Select the //CAN-bus BMS (500 kbits/s)// CAN-profile in the CCGX. Menu path: //Settings -> Services -> CAN-profile// | + | * Select the //CAN-bus BMS (500 kbits/s)// CAN-profile in the [[venus-os: |
* After properly wiring and setting up, the AXIstorage will be visible as a battery in the device list:{{ : | * After properly wiring and setting up, the AXIstorage will be visible as a battery in the device list:{{ : | ||
* The parameters option within the battery page shows the actual battery charge and discharge limits:{{ : | * The parameters option within the battery page shows the actual battery charge and discharge limits:{{ : | ||
+ | |||
===== DISQUS ===== | ===== DISQUS ===== | ||
~~DISQUS~~ | ~~DISQUS~~ | ||
+ |
battery_compatibility/axistorage.1505466454.txt.gz · Last modified: 2017-09-15 11:07 by edevries