battery_compatibility:bmz_ess
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
battery_compatibility:bmz_ess [2017-01-16 14:45] – [4. Color Control GX Configuration] edevries | battery_compatibility:bmz_ess [2022-07-18 12:05] (current) – typo dfaber | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Victron & BMZ ESS 3.0 / ESS 7.0 ===== | + | ====== Victron & BMZ ===== |
+ | |||
+ | The combination of Victron products with the BMZ ESS battery has been tested and certified by the R&D departments. The combination is actively supported by both companies. | ||
+ | |||
+ | Compatible BMZ models: | ||
+ | |||
+ | * ESS 7.0 | ||
+ | * ESS 9.0 | ||
+ | * ESS X | ||
+ | * ESS Z | ||
==== 1. Introduction ==== | ==== 1. Introduction ==== | ||
=== 1.1 Compatible Victron products === | === 1.1 Compatible Victron products === | ||
- | All 48V Multis and Quattros. And always a Color Control | + | All 48V Multis and Quattros. And always a [[venus-os: |
=== 1.2 Notes === | === 1.2 Notes === | ||
Line 9: | Line 18: | ||
* Paralleling multiple BMZ ESS batteries to expand capacity is possible. Contact BMZ for more information. | * Paralleling multiple BMZ ESS batteries to expand capacity is possible. Contact BMZ for more information. | ||
* Derating, based on the dynamic BMZ ESS charge- and discharge limits: | * Derating, based on the dynamic BMZ ESS charge- and discharge limits: | ||
- | * Minimum | + | * Minimum |
* The derating mechanism is not very precise yet. In other words, do not expect a discharge limit of 30A to result in a precise discharge of 30A. | * The derating mechanism is not very precise yet. In other words, do not expect a discharge limit of 30A to result in a precise discharge of 30A. | ||
* Actual charge- and discharge limits are visible in the Parameters page. See screenshot below in Chapter 4. | * Actual charge- and discharge limits are visible in the Parameters page. See screenshot below in Chapter 4. | ||
+ | * BMZ batteries and MPPT Solar Chargers with a VE.Can communication port cannot be both connected to the CCGX, because of different canbus speeds. Use a Cerbo GX, or Solar Chargers with a VE.Direct comm. port instead. | ||
=== 1.3 System diagram === | === 1.3 System diagram === | ||
{{ : | {{ : | ||
- | ==== 2. Wiring of communication cables | + | ==== 2. GX device needed |
- | To use the BMZ ESS in Victron system, it is necessary to use a Color Control GX. The Color Control GX takes care of sending | + | To use the BMZ ESS in Victron system, it is necessary to use a Color Control |
- | A special RJ-45 cable is necessary to connect the battery to the Color Control GX. Pinout: | ||
- | ^ Function ^ VE.Can | + | ==== 3. Wiring of communication cables ==== |
- | | GND | Pin 3 | Pin 2 | | + | Use the //VE.Can |
- | | CAN-L | + | |
- | | CAN-H | + | |
- | Place a VE.Can terminator in the empty socket on the CCGX | + | Then, plug a [[https:// |
- | ==== 3. VEConfigure settings ==== | + | More information about the cable can be found in [[battery_compatibility: |
- | === 3.1 Charge tab === | + | |
+ | Without properly connecting this cable, the battery will stop charging/ | ||
+ | |||
+ | ==== 4. VEConfigure settings ==== | ||
+ | |||
+ | === 4.1 General tab === | ||
+ | - Check " | ||
+ | - Enter the battery capacity: | ||
+ | - BMZ ESS 7.0 - 121.5 Ah | ||
+ | - BMZ ESS 9.0 - 156.6 Ah | ||
+ | - BMZ ESS X - 186.3 Ah | ||
+ | - BMZ ESS Z - 162 Ah | ||
+ | - The other parameters (" | ||
+ | |||
+ | === 4.2 Charger | ||
^ Parameter | ^ Parameter | ||
| Battery type | Lithium | | | Battery type | Lithium | | ||
| Charge curve | Fixed | | Charge curve | Fixed | ||
- | | Absorption voltage | + | | Absorption voltage |
- | | Float voltage | + | | Float voltage |
| Absorption time | 1 Hr | | | Absorption time | 1 Hr | | ||
- | Note: make sure to double check the float voltage after completing Assistants, and if necessary set it back to 56.7 V. | + | Note: make sure to double check the float voltage after completing Assistants, and if necessary set it back to 60.00 V. |
- | === 3.2 ESS Assistant === | + | === 4.3 ESS Assistant === |
Select the fourth battery type: | Select the fourth battery type: | ||
Line 45: | Line 66: | ||
Then: | Then: | ||
- | - Enter the battery capacity: | ||
- | - BMZ ESS 3.0 - 121.5 Ah | ||
- | - BMZ ESS 7.0 - 121.5 Ah | ||
- Do not change the dynamic cut-off values, they have already been set correctly after selecting the lithium battery type. | - Do not change the dynamic cut-off values, they have already been set correctly after selecting the lithium battery type. | ||
+ | - Sustain voltage: 50V | ||
- Same for the restart offset: do not change that. | - Same for the restart offset: do not change that. | ||
- | ==== 4. Color Control | + | ==== 5. GX device |
- | * Enable | + | * Select |
* After properly wiring and setting up, the BMZ ESS will be visible as a battery in the device list:{{ : | * After properly wiring and setting up, the BMZ ESS will be visible as a battery in the device list:{{ : | ||
* The parameters option within the battery page shows the actual battery charge and discharge limits:{{ : | * The parameters option within the battery page shows the actual battery charge and discharge limits:{{ : | ||
- | * Make sure to enable the // | + | |
+ | ==== 6. DVCC Settings ==== | ||
+ | |||
+ | Enabling DVCC changes a GX device from a passive monitor into an active controller. The available features and effects of enabling DVCC depend on the type of battery used. The effect also depends on the installed Victron components and their configuration. | ||
+ | |||
+ | This table shows the recommend settings for different battery types: | ||
+ | |||
+ | {{ : | ||
===== DISQUS ===== | ===== DISQUS ===== | ||
~~DISQUS~~ | ~~DISQUS~~ | ||
+ |
battery_compatibility/bmz_ess.1484574355.txt.gz · Last modified: 2017-01-16 14:45 by edevries