ccgx:ccgx_wireless_ac_sensor
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
drafts:ccgx:ccgx_wireless_ac_sensor [2014-10-30 10:21] – [Installation] mvader | ccgx:ccgx_wireless_ac_sensor [2021-03-20 03:05] (current) – guystewart | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Wireless AC Sensor manual | + | ====== Wireless AC Sensor manual ====== |
+ | (discontinued product) | ||
===== Introduction ===== | ===== Introduction ===== | ||
- | The Wireless AC sensors are used to measure PV Inverter | + | The Wireless AC sensors are used to measure |
- | [ add measurement accuracy etc. or at the end of this doc. ] | + | Note that it is not possible to use multiple sensors on the same position (AC-Out, AC-In 1, etcetera) in a system. The GX device will in such case only show the value of the last-read sensor. |
+ | |||
+ | ==== Three phase ==== | ||
+ | |||
+ | For measuring a three phase system, we recommend to use [[https:// | ||
===== Required hardware ===== | ===== Required hardware ===== | ||
Line 13: | Line 18: | ||
Included with the gateway: | Included with the gateway: | ||
- | | + | |
+ | | ||
* AC adapter | * AC adapter | ||
- | {{ : | + | {{ : |
+ | |||
===== Installation ===== | ===== Installation ===== | ||
Line 23: | Line 31: | ||
- Disconnect the AC power | - Disconnect the AC power | ||
- | - Connect the gateway to the network using the supplied RJ45 cable. | + | - Connect the gateway to the Ethernet/ |
- | - Connect the AC power adapter to the gateway | + | - Connect the AC power adapter |
=== Installing the sensor(s) === | === Installing the sensor(s) === | ||
- | For each phase, connect the AC sensor according to the schematic below. Neutral on top side. Line on bottom side. Make sure the direction of the current is correct | + | For each phase, connect the AC sensor according to the schematic below. Neutral on top side. Line on bottom side. Make sure the direction of the current is correct. |
- | + | {{ : | |
- | [ plaatje ] | + | |
===== Gateway and sensor pairing ===== | ===== Gateway and sensor pairing ===== | ||
- | After powering | + | After powering the sensor for the first time, it needs to be paired with the gateway. The led on the sensor will be blinking red, to indicate that it is not yet paired to a gateway. |
If it is not blinking red, but both the green and the red LED are on, it needs to be unpaired first: press and hold the little reset button in the sensor. As soon as you press the button the LED will turn green. Hold the button until the LED starts blinking red. | If it is not blinking red, but both the green and the red LED are on, it needs to be unpaired first: press and hold the little reset button in the sensor. As soon as you press the button the LED will turn green. Hold the button until the LED starts blinking red. | ||
Line 54: | Line 61: | ||
^LED ^Meaning | | ^LED ^Meaning | | ||
|Blinking red |Not yet paired to a gateway | | |Blinking red |Not yet paired to a gateway | | ||
- | |Both green and red on (no blinking) |Cannot find the gateway | | + | |Both green and red on (no blinking) |Cannot find the gateway. Only shows for a few seconds, after that the led will turn off | |
- | |Alternating red/green |Selected in the Color Control | + | |Alternating red/green |Selected in the GX device |
|Green on (no blinking) |Gateway found, connecting. This will show only for a few seconds | | |Green on (no blinking) |Gateway found, connecting. This will show only for a few seconds | | ||
- | |Off |Working OK, connected to the gateway, or not powered | | + | |Off |Working OK, connected to the gateway, |
- | ===== Configuration on the Color Control | + | ===== Configuration on the GX device |
+ | |||
+ | ==== Wireless AC sensor menu ==== | ||
+ | |||
+ | To configure the gateway and sensor go to the Wireless AC sensor menu | ||
+ | |||
+ | Settings → Wireless AC Sensors | ||
+ | |||
+ | If the gateway is connect to the network it will be shown in the list. If one or more AC sensors are connected these will also show in the list. When connected for the first time only the ID number will be shown and no location. This needs to be selected for the sensor to work properly. | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | Select a sensor to assign a location to it. For example AC-In1_L3. | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | === Sensor readout === | ||
+ | |||
+ | When all the sensor are configured the measured values can be seen. Go to the Device List and select PV Inverter on AC In1 for example. | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | === Specifications === | ||
+ | |||
+ | ^ ^ ^ | | ||
+ | |Rated voltage |230 |V AC | | ||
+ | |Operating Voltage |220-240 |V AC | | ||
+ | |Frequency |50 |HZ | | ||
+ | |Maximum Current |25 |A | | ||
+ | | | | | | ||
+ | |Measurement precision | +/- 2% | | | ||
+ | | | | | | ||
+ | |Ambient temperature |-25 ~ +35 |oC | | ||
+ | |Storage temperature |-25 ~ +70 |oC | | ||
+ | |Relative humidity |0 - 95 |% | | ||
- | ~~DISQUS~~ | ||
\\ | \\ | ||
+ | |||
+ | ===== DISQUS ===== | ||
+ | ~~DISQUS~~ | ||
ccgx/ccgx_wireless_ac_sensor.1414660877.txt.gz · Last modified: 2014-10-30 10:21 by mvader